Metal detector or X-ray: Which system is right for your food production line?

If metal is your only realistic foreign object risk and you are not packaging in aluminum, a metal detector is usually sufficient. X-ray inspection is worthwhile if glass, stone, bone, or dense plastics are documented hazards, if you need to inspect products in aluminum or metal packaging, or if you want to simultaneously check fill levels and product completeness. A test with your product will provide clarity.

RaymanTech Editorial Team
27.10.2026
Metal detector or X-ray: Which system is right for your food production line?

Auf einen Blick

  • A metal detector identifies iron, non-ferrous metals, and stainless steel; it is more affordable, compact, also available as a free-fall or pipeline unit, and is not subject to radiation protection regulations.
  • An X-ray system detects anything significantly denser than the product itself—including glass, stone, bone, and certain plastics—works with aluminum packaging, and can also verify fill levels and product completeness.
  • X-ray technology has its limitations: according to IFS standards, polypropylene and nylon are considered undetectable, and thin stainless steel in lightweight products is often harder to detect than with a metal detector.
  • The BRCGS standard requires metal detection; opting out is only possible with a documented risk assessment and a more effective alternative, such as X-ray inspection.
  • In Germany, a fully shielded X-ray device with type approval only requires registration and does not need a radiation protection officer, though it must be inspected by an expert every five years.

This decision-making guide is based on primary sources: the IFS Foreign Body Management Guideline (2025), the BRCGS Food Safety Standard (Issue 9, 2022), the German Radiation Protection Ordinance, and data from the EU Rapid Alert System. RaymanTech offers both technologies, X-ray inspection systems as well as Metal detectors for the food industry. We therefore have no interest in recommending the more expensive device to you.

What does each method detect?

A metal detector detects metal, while an X-ray system detects differences in density. Almost everything else follows from this.

The metal detector generates an alternating electromagnetic field. Conductive or magnetic parts disrupt this field. Iron is the easiest to find, while non-magnetic stainless steel is the most difficult. It is less well known that the orientation of a part plays a role. According to the IFS Foreign Body Management Guideline (IFS, 2025), a wire-shaped iron part is detected well when aligned longitudinally to the direction of transport, but poorly when aligned transversely. For non-ferrous metal and non-magnetic stainless steel, it is exactly the opposite. Shavings provide an even weaker signal than wire.

The X-ray system measures how much radiation the product absorbs. A foreign body is only noticeable if it is significantly denser than its surroundings. The IFS Guideline (2025) classifies this for water-containing foods (density 1.00 g/cm³) as follows:

  • Not detectable: Hair (0.32 g/cm³), cherry pit (0.56), insects (0.59), wood (0.65), polypropylene (0.90), nylon (1.15)
  • Detectable depending on the product: PVC (1.70 g/cm³), Teflon (2.19), bone (2.20), stone (2.52), glass (2.60), aluminum (2.71), stainless steel (7.93)

The detection of plastic is therefore never guaranteed. Whether a plastic part becomes visible depends on the material, size, orientation, and product, and this can only be clarified through testing. In poultry, thin, poorly calcified bones are close to muscle tissue in terms of density. For such cases, dual-energy X-ray systems are intended, which evaluate two energy ranges.

Which foreign bodies are actually reported?

Glass and metal lead the EU reports, with plastic in third place. An analysis of the EU Rapid Alert System for Food and Feed (RASFF) (Microplastics/MDPI, 2024) found a total of 402 reports regarding glass, metal, plastic, insects, and bones between 2020 and 2023; plastic accounted for 25.1%. 90.4% of glass reports, 77.9% of metal reports, and 65.3% of plastic reports were classified as a serious risk. In Germany, according to the Federal Association of Food Chemists in Public Service (BLC, 2026), 51 reports on lebensmittelwarnung.de cited foreign bodies as the reason in 2025.

How do metal detectors and X-ray systems differ in a direct comparison?

X-ray covers more types of foreign bodies and packaging, while the metal detector is more cost-effective and has an advantage when it comes to finding certain metals. The table shows the most important differences.

product quality, but it is not the better metal detector for every product. The deciding factor is which hazards your HACCP analysis documents and how your product is packaged.

Kriterium Metalldetektor Röntgeninspektion
Prinzip Störung eines elektromagnetischen Feldes Absorption von Röntgenstrahlung (Dichte × Dicke)
Eisen / Nichteisen / Edelstahl Ja; Edelstahl am schwierigsten, Lage des Teils entscheidend Ja, solange das Teil genug Kontrast erzeugt
Dünner Edelstahl in leichtem Produkt Oft im Vorteil Oft im Nachteil (schwacher Kontrast)
Glas, Stein, Keramik Nein Ja, je nach Produkt
Kalzifizierte Knochen Nein Ja, je nach Produkt; dünne Geflügelknochen schwierig
Kunststoffe Nur metalldetektierbare Spezialkunststoffe Nur dichte Kunststoffe (z. B. PVC, PTFE); PP und Nylon nicht
Produkteffekt (nass, salzig, warm) Senkt die erreichbare Empfindlichkeit Kaum relevant; Dicke und Homogenität zählen
Alufolie, Aluschale, Dose Nur Eisen erkennbar, mit Ferrous-in-Foil-Geräten Ja
Füllstand, fehlende Teile, Siegelnaht Nein Ja
Bauformen Band, Freifall, Rohrleitung Band, auch Rohrleitung und Schüttgut
Auflagen Keine besonderen Strahlenschutzrecht (Anzeige oder Genehmigung)
Kosten Niedriger Höher; Generator und Detektor sind Verschleißteile

How small are the detection limits in ongoing production?

In the production line, detection limits are usually significantly higher than the best-case values found in data sheets because the product and packaging are contributing factors. For example: According to its data sheet, the RaymanTech dual-energy system RXD-MS-2416 achieves a best-case detection of a 0.3 mm stainless steel sphere and a 0.8 mm glass sphere. The IFS Guideline (2025), by contrast, lists typical sizes that X-ray systems detect in everyday production (sphere diameter):

Fremdkörper Kunststoff/Papier Metallisierte Folie Dose Glas
Metall 0,8 mm 0,8 mm 1,2 mm 1,2 mm
Aluminium 2,0 mm 2,0 mm 2,5 mm 2,5 mm
Glas, Stein 2,0 mm 2,0 mm 3,0 mm 3,0 mm
Knochen, dichter Kunststoff 3,5 mm 3,5 mm 5,0 mm 5,0 mm

‍

Key takeaway: For cans and jars, typical X-ray detection limits are about 50% higher than those for plastic or paper packaging. Plan based on your product's specific values, not the best-case figures from a brochure.

It is similar with metal detectors. In a real-world case from the IFSQN professional forum, limits of 6 to 8 mm were agreed upon for frozen meat blocks—far above the 1.5 to 2.5 mm cited in many guides. This is an individual case, but it demonstrates that the values achievable for your product can only be determined using your product.

How do product and packaging influence detection?

With metal detectors, conductive products reduce sensitivity; with X-rays, thickness, density, and homogeneity are the deciding factors. Wet, salty, warm, or frozen products conduct electricity themselves. The metal detector must filter out this inherent signal, which reduces its sensitivity. Multi-frequency technology mitigates this effect but does not eliminate it. With X-rays, conductivity and temperature play almost no role: the more uniform the product, the smaller the detectable foreign object.

Does a metal detector work with aluminum foil and aluminum trays?

To a limited extent, yes—specifically for ferrous parts. It is often said that metal detectors are fundamentally unsuitable here, but ferrous-in-foil detectors can detect iron even in aluminum packaging. The BRCGS standard (Issue 9, 2022, clause 4.10.3.4) explicitly allows for products in foil containers to be tested using only a ferrous test piece. However, non-ferrous metal, stainless steel, glass, and bone remain detectable in aluminum packaging only via X-ray. Alternatively, you can inspect with the metal detector before packaging.

What does an X-ray system check for in addition to foreign objects?

An X-ray system can also monitor fill levels, completeness, seal integrity, and shape defects using the same scan. It detects fill levels in opaque containers, missing or broken parts, and product trapped in the seal. Mass can also be estimated via grayscale values. If you currently have separate inspection steps for these tasks, this consolidation should be included in your cost-benefit analysis. Learn more in our X-ray scanners for food.

Do IFS or BRCGS mandate X-ray inspection?

No, none of the major standards mandate X-ray inspection. According to the BRCGS Food Safety Standard (Issue 9, 2022, clause 4.10.3.1), metal detection is the standard procedure. A facility can only opt out if a risk assessment shows that metal detection does not improve food safety. Such an exemption is generally based on a more effective method, such as X-ray, fine sieves, or filtration, and must be documented.

For both methods, testing requires: test pieces with a known, risk-based diameter, at normal belt speed, with proof of detection and rejection. However, the BRCGS standard specifies different test positions. For a metal detector, the test piece belongs in the center of the aperture, where the field is weakest. For X-ray, it belongs in the least sensitive area, which may be near the radiation source or near the detector. A test routine adopted from a metal detector may therefore be testing in the wrong place when using X-ray.

In practice, test piece sizes are often dictated by retail customers through their own requirements. A metal detector alone, for example, cannot fulfill a "zero glass" policy. We describe in detail how metal detectors are integrated as CCPs in our Metal detectors for the food industry.

What do the systems cost, and what applies to radiation protection?

A metal detector is less expensive to purchase and operate than an X-ray system. With X-ray, wear parts are added to the purchase price: according to manufacturer specifications, the X-ray generator and line detector are the most expensive replacement parts, in addition to cooling and regular inspections. Therefore, compare quotes over the entire service life, including maintenance, spare parts, and mandatory inspections.

What radiation protection requirements apply in Germany?

For a fully shielded device with type approval, the effort is less than many expect:

  • According to § 21 of the Radiation Protection Ordinance (StrlSchV), a fully shielded device must not emit more than 3 µSv/h at a distance of 0.1 m from the housing and requires two independent safety devices.
  • With a valid type approval, a notification to the responsible state authority is sufficient according to the DGUV. A radiation protection officer with specialized knowledge is not required. However, the device must be inspected every five years by an officially appointed expert (§ 88 para. 4 StrlSchV).
  • According to the DGUV, dosimeter monitoring is not necessary for employees working with such devices. The annual dose remains below 1 mSv during intended operation.
  • Without type approval, authorization including a radiation protection officer may be necessary. Therefore, clarify the approval status of the specific device before purchasing.

Does the inspection process irradiate the food?

Not in the sense of food law. The Codex Alimentarius standard for irradiated foods (CXS 106-1983, Rev. 2003) explicitly does not apply to radiation from inspection equipment. The US FDA limits the dose from inspection X-ray tubes up to 500 kVp to a maximum of 10 Gray (21 CFR 179.21).

What do false rejects cost?

False rejects cost money with both methods and should therefore be part of every test. A user on the IFSQN forum reports a false reject rate of around 0.54% on a pouch line despite fine-tuning; the causes were particles in the packaging and changing laminates. When conducting a product test, make sure to ask for the false reject rate in addition to the detection limit.

When does it make sense to combine both systems?

A combination is worthwhile when different hazards exist at different points in the line. A typical pattern: a metal detector protects the equipment at the goods-in stage or before slicers and mills, while an X-ray system checks the packaged product at the end of the line for glass, stone, bone, and completeness. For raw produce from the field, such as nuts or vegetables, it can also be the other way around.

Decision-making in five questions

  1. Does your HACCP analysis identify glass, stone, bone, or dense plastics as a hazard? Yes: consider X-ray.
  2. Do you package in aluminum or cans and are unable to inspect before sealing? Yes: X-ray; for purely ferrous hazards, consider "ferrous-in-foil" technology.
  3. Is your product thin, light, and dry, and is stainless steel the primary hazard? Yes: test a metal detector first.
  4. Do you currently check fill levels or completeness separately? Yes: include X-ray in your cost analysis.
  5. Are there different hazards at the goods-in stage and the end of the line? Yes: plan for a combination.

Our assessment

For most lines with a purely metal risk and plastic or paper packaging, a well-adjusted metal detector remains the most economical solution. We recommend X-ray as soon as non-metallic hazards are documented or inspection must take place within metal packaging, as a metal detector cannot physically perform this task. For an overview of all methods, see our page on Foreign object detection in production.

Test instead of guess

RaymanTech offers trial installations. Contact us if you would like to have your product tested in its original packaging. We will tell you honestly whether a metal detector, an X-ray system, or both make sense for your line: Request a product test at RaymanTech.

Passende Lösung von RaymanTech

Sie möchten wissen, wie sich das in Ihrer Linie umsetzen lässt? Auf der passenden Produktseite finden Sie Technik, Bauformen und Einsatzbereiche im Detail. Für eine Einschätzung Ihrer Anwendung sprechen Sie direkt mit unseren Inspektionsexperten.

Produkttest anfragen

Frequently Asked Questions about Metal Detectors and X-ray Inspection

Metal detector or X-ray inspection system – which is better?

Neither is inherently better. X-ray systems detect a wider range of foreign objects and work effectively with aluminum packaging. Metal detectors are more cost-effective, easier to integrate into existing lines, and often more sensitive when detecting thin stainless steel in lightweight products. The deciding factors are your documented hazards and your specific packaging.

Can X-rays detect plastic?

Only dense plastics such as PVC or PTFE are detectable, and even then, only depending on the product and size. According to the IFS guidelines (2025), polypropylene and nylon are considered non-detectable. There is no guarantee for the detection of plastic.

Can metal detectors scan through aluminum foil?

Limited capability: Ferrous-in-foil systems can only detect ferrous metal parts. For non-ferrous metals, stainless steel, and non-metallic contaminants in aluminum packaging, X-ray inspection is required, or alternatively, metal detection prior to packaging.

Is X-ray inspection safe for food and employees?

Inspection is not considered food irradiation (Codex CXS 106). In accordance with § 21 of the Radiation Protection Ordinance (StrlSchV), fully shielded devices must not emit more than 3 µSv/h at a distance of 0.1 m, and according to DGUV regulations, the annual dose for employees remains below 1 mSv.

Does IFS or BRCGS require an X-ray machine?

No. BRCGS requires metal detection. It is possible to waive this requirement with a risk assessment, typically if a more effective method such as X-ray is used. Retail customers may impose stricter requirements.

Quellen

Weitere Wissensartikel

Get your personal demo

Our product specialists will help you find the perfect machines for your requirements

Name
Company
Email
Phone number
Thank you! Your submission has been received!
Oops! Something went wrong while submitting the form.
By submitting this form you agree with our Privacy Policy.