Standards for metal detection in the food industry: What IFS, BRCGS, and FSSC 22000 specifically require

None of the major standards for the food industry mandate a fixed test piece size for metal detectors. IFS Food 8, BRCGS Issue 9, and FSSC 22000 require you to define, validate, and document sensitivity, testing frequency, rejection, and record-keeping based on your risk analysis. Specific millimeter values only arise from retailer requirements, your HACCP plan, and validation using your own products.

RaymanTech Editorial Team
27.10.2026
Standards for metal detection in the food industry: What IFS, BRCGS, and FSSC 22000 specifically require

Auf einen Blick

  • According to BRCGS Issue 9 (clause 4.10.3.1), metal detection is mandatory unless a documented risk analysis justifies a more effective alternative such as X-ray, fine sieves, or filtration.
  • IFS Food 8 (clause 4.12.4) requires that metal detectors be serviced at least once every 12 months.
  • Anyone opting out of foreign body detection under FSSC 22000 Version 6 (additional requirement 2.5.11 d) must provide a written justification.
  • Test pieces for metal detectors are spheres with a known, risk-based diameter, labeled by size and material, and separated into ferrous, stainless steel, and typically non-ferrous.
  • If a test fails, all products processed since the last successful test must be quarantined and re-inspected; therefore, the testing interval determines the quantity of affected goods.

This article examines the clauses applicable to metal detection in the food industry, identifying where the standards are clear and where the frequently cited "standard values" do not actually originate from the standards themselves.

Which regulations apply to metal detection?

There are three levels of regulation for metal detection that are often conflated: legislation, certification standards, and customer requirements.

  • Legislation: Regulation (EC) No 178/2002 prohibits the placing of unsafe food on the market in Article 14, while Article 19 governs withdrawals and recalls. Regulation (EC) No 852/2004 mandates procedures based on HACCP principles in Article 5. There is no EU law that prescribes a specific metal detector or test piece size.
  • Certification standards: IFS Food, BRCGS Food Safety, and FSSC 22000 (all GFSI-recognized) translate the obligation to control hazards into verifiable requirements.
  • Customer requirements: Codes of Practice from major retailers can define specific sensitivities and fail-safe equipment. This explains why two IFS-certified facilities might use completely different test pieces.

IFS Food Version 8

IFS Food 8 has been mandatory for audits since January 1, 2024 (IFS, 2023). Chapter 4.12 is critical for metal detection:

  • 4.12.1 (KO Requirement No. 6): Risk-based procedures to prevent foreign body contamination; contaminated products are considered non-conforming. A violation can result in the loss of certification.
  • 4.12.4: Where metal or other foreign body detectors are required, they must be installed for maximum detection efficiency and serviced at least once every 12 months, as well as following any significant changes.
  • 4.12.5: The accuracy of detection equipment must be defined, and functional tests must be performed at a risk-based frequency; in the event of a malfunction, the impact on products and processes must be assessed.
  • 4.12.6: Potentially contaminated products must be isolated, with access restricted to authorized personnel only.

BRCGS Global Standard Food Safety Issue 9

BRCGS is significantly more specific (BRCGS, 2022):

  • 4.10.3.1: Metal detection must be in place unless a risk analysis shows that it does not improve food safety. Any decision not to use it must be justified in writing and is typically based on a more effective method such as X-ray, fine sieving, or filtration.
  • 4.10.3.2: The detector requires one of three solutions: automatic rejection into a secure unit accessible only to authorized personnel, a belt stop with an alarm (e.g., for very large containers), or inline detection of the foreign object.
  • 4.10.3.4: Minimum content for testing procedures; details are in the section on test pieces.
  • 4.10.1.3: The frequency of testing must take into account customer requirements and the ability to identify and isolate affected goods in the event of a failure.

FSSC 22000

FSSC 22000 is based on ISO 22000 and the prerequisite programs of the ISO/TS 22002 series. Additional requirement 2.5.11 (d) from version 6 requires a risk assessment that determines the need for and type of foreign object detection; if a facility decides against it, the justification must be available as documented information. Audit practice shows that this is not just a formality: according to the Foundation FSSC (2026), physical contamination is one of the most frequent non-conformities in version 6 audits. For your audit, the wording of the scheme version under which you are certified is always the authoritative source.

HACCP: Metal detector as a CCP

If metal detection is classified as a Critical Control Point (CCP), the following applies: the critical limit is the validated sensitivity per metal type, monitoring is the test piece check, and the corrective action is to isolate and re-test. Consequently, test piece size, testing frequency, and documentation are directly tied to your HACCP plan rather than an external standard.

Anforderung IFS Food 8 BRCGS Issue 9 FSSC 22000 v6
Metalldetektor Pflicht? Wo laut Risikoanalyse erforderlich (4.12.4) Ja, außer Risikoanalyse begründet Alternative (4.10.3.1) Risikobewertung entscheidet, Verzicht schriftlich begründen (2.5.11 d)
Testkörpergröße Genauigkeit festlegen, keine mm-Angabe (4.12.5) Kugel mit bekanntem Durchmesser, risikobasiert, gekennzeichnet; keine mm‑Angabe (4.10.3.4) Keine Vorgabe
Prüfhäufigkeit Risikobasiert (4.12.5) Nach Kundenvorgaben und Sperrfähigkeit; Inline-Detektoren bei Anlauf und Produktionsende (4.10.1.3, 4.10.3.4) Über dokumentiertes Verfahren, keine Zahl
Ausschleusung / Fail-Safe Isolierung, nur autorisiertes Personal (4.12.6) Gesicherte Ausschleusung, Bandstopp oder Ortung (4.10.3.2); Fail-Safe-Systeme prüfen (4.10.3.4) Dokumentiertes Verfahren für Einsatz und Management der Geräte
Wartung Mindestens 1× in 12 Monaten (4.12.4) Keine eigene Frist in 4.10.3 Keine eigene Frist
Fehlerfall Auswirkungen bewerten (4.12.5) Alle Produkte seit letztem erfolgreichem Test isolieren und nachprüfen (4.10.1.3) Über Korrekturmaßnahmen nach ISO 22000

‍

Key takeaway: None of the three standards specifies a test piece size in millimeters; all require a justified, validated, and documented determination. BRCGS is most specific regarding rejection and testing procedures, while IFS is more specific regarding maintenance with its 12-month deadline.

What test piece sizes are required for Fe, non-Fe, and stainless steel?

Neither IFS Food 8 nor BRCGS Issue 9 prescribes fixed test piece sizes for iron, non-ferrous metals, and stainless steel. Values such as "3 mm iron, 4 mm non-ferrous, 4 mm stainless steel" are often referred to as the standard, but they do not appear in the standard texts. According to BRCGS 4.10.3.4, only the procedure is binding:

  • Test pieces with a metal sphere of a known diameter, selected based on risk and labeled with size and material.
  • Separate test pieces for iron (Fe), stainless steel, and generally non-ferrous (non-Fe); for products in aluminum packaging, a pure iron test may suffice.
  • Proof that detection and rejection function under normal operating conditions, using several test packages in succession at typical belt speed.
  • Pass test pieces through the center of the aperture whenever possible, as sensitivity is lowest there, and ideally within a labeled product package.

The IFS guideline for effective foreign body management (Version 3, IFS 2025) adds: test pieces should be as small as possible, customer specifications must be taken into account, and damaged test pieces must be replaced. It also points out an effect that test spheres do not replicate: a rod-shaped iron object (e.g., wire) is detected well when aligned with the direction of travel, but poorly when positioned crosswise or upright; for non-ferrous and non-magnetic stainless steel, the opposite is true. Shavings produce an even weaker signal than wire.

A figure from US authorities serves as an upper-limit guideline: the FDA classifies hard or sharp foreign bodies between 7 and 25 mm in length in ready-to-eat products as adulteration. According to the FDA, such foreign bodies rarely cause injury if they are under 7 mm, except in high-risk groups such as infants, surgical patients, and the elderly (FDA, CPG Sec. 555.425, 2005). For baby food or hospital meals, your test pieces should therefore be chosen to be significantly smaller.

Our recommendation: Define the test piece size as the smallest sphere that your system reliably detects and rejects with your product, your packaging, and your aperture size at full belt speed, and document this validation. Do not adopt values from tables that you have not confirmed with your own product.

How often must the metal detector be tested?

According to BRCGS, an inline metal detector must be tested at least at the start and end of production; the frequency in between must take into account customer requirements and your ability to quarantine products (4.10.1.3, 4.10.3.4). IFS refers to a risk-based frequency (4.12.5). Common additional occasions in practice include product changes, program changes, malfunctions, and cleaning.

The crucial connection is stated in BRCGS 4.10.1.3: If a test fails, all products since the last successful test must be isolated, quarantined, and re-examined. Your test interval is therefore not just a formality; it determines how much stock you must hold back in the event of a failure. A calculation example: at 60 packs per minute, a two-hour interval means up to 7,200 packs that must be re-tested.

Also, pay attention to belt speed: the IFS guideline (2025) points out that in start-stop operation, the speed may drop below the critical transport speed; products that were in the tunnel at that moment should be re-tested.

What fail-safe functions must a metal detector have?

BRCGS does not definitively specify exactly which fail-safe functions a metal detector must have, but it does require that the fail-safe systems for detection and rejection be tested during routine checks (4.10.3.4). The IFS guideline (2025) is more specific: it mentions sensors for compressed air failure, for rejection confirmation, and for a full rejection bin.

Retailer codes of practice may go beyond this. According to an overview by Thermo Fisher Scientific (2019) on retailer requirements, these include, for example:

  • Sensors that trigger an alarm if they fail themselves
  • Alarm for missing rejection confirmation
  • Alarm for a full, open, or unlocked rejection bin
  • Alarm for compressed air failure (pusher, air blast)
  • Alarm for a malfunction of the detector itself
  • Alarms that remain active after a power failure or restart and can only be acknowledged by an authorized person

The requirements of your own customers are the deciding factor. Clarify these before making a new purchase, as retrofitting confirmation sensors and locked bins is usually more complex than having them installed at the factory.

What belongs in a metal detector's test log?

A test log must at least include the product, the tester, the time, the test piece, the result, and any actions taken. BRCGS 4.10.3.3 requires a procedure with defined responsibilities, sensitivity per product, method and frequency of testing, and recording of results. The IFS guideline (2025) lists the following as minimum contents for a test entry:

  • Product and line
  • Inspector
  • Date and time
  • Test piece used (material, diameter)
  • Test result (detected and rejected: yes/no)
  • Corrective actions for deviations
  • Signature or entry in the data acquisition system

Add the time of the last successful test, as this defines the scope of the quarantine in the event of a failure.

How do metal detectors work in the food industry?

Most metal detectors in the food industry use a balanced coil system: a metal object disrupts the electromagnetic field as it passes through, and the signal triggers the rejection process. Different designs are used depending on the product:

  • Conveyor belt detectors for packaged and unpackaged individual items
  • Gravity-fed detectors for bulk materials such as flour, sugar, or nuts
  • Pipeline detectors for pumpable products such as sauces or sausage meat

Moist, salty, or warm products generate their own signal (product effect), which limits the achievable sensitivity, especially with stainless steel. You can find an overview of designs in our summary of metal detectors for product inspection; we showcase industry-specific versions in the Metal detectors for the food industry.

Limitations: Metal detectors cannot detect glass, stone, bone, or plastic. In these cases, an X-ray scanners for food can help, though only for foreign objects that are denser than the product itself. The IFS Guideline (2025), for example, classifies polypropylene (0.90 g/cm³) in water-based foods as non-detectable, while PVC (1.70 g/cm³) is considered detectable depending on the product and size. Plastic detection is therefore never guaranteed. We describe which methods are suitable for specific foreign object risks under Foreign object detection in product inspection.

How do you implement standard requirements on your production line?

Whether your line meets the requirements of IFS, BRCGS, or your retail specifications depends on your product: product effect, aperture size, belt speed, and rejection systems. RaymanTech supports you in selecting the appropriate Metal detectors for the food industry and with validation for your specific application. To get an assessment of your line, please feel free to use the consultation with the RaymanTech team.

Passende Lösung von RaymanTech

Sie möchten wissen, wie sich das in Ihrer Linie umsetzen lässt? Auf der passenden Produktseite finden Sie Technik, Bauformen und Einsatzbereiche im Detail. Für eine Einschätzung Ihrer Anwendung sprechen Sie direkt mit unseren Inspektionsexperten.

Metalldetektoren für die Lebensmittelindustrie ansehen

Frequently Asked Questions About Metal Detection Standards

Is there a legal requirement for metal detectors in the food industry?

No, there is no EU law that mandates the use of a metal detector. Regulation (EC) No 852/2004 requires a HACCP-based procedure, and Regulation (EC) No 178/2002 prohibits unsafe food. In practice, the requirement for a detector arises from BRCGS Issue 9 (4.10.3.1), risk analyses conducted in accordance with IFS or FSSC 22000, and specific customer requirements.

What test piece sizes do IFS or BRCGS specify?

IFS and BRCGS do not mandate specific test piece sizes. BRCGS requires spherical test pieces with a known diameter chosen based on risk, labeled by size and material, and separated into ferrous, stainless steel, and typically non-ferrous categories. You define the specific millimeter values through validation or according to retailer specifications.

How often does a metal detector need to be tested?

According to BRCGS, an inline metal detector must be tested at least at the start and end of production, with additional testing in between at a frequency that accounts for customer requirements and your ability to quarantine products. IFS requires a risk-based frequency. The longer the interval, the more product you will need to quarantine and re-inspect in the event of a failed test.

How often does a metal detector need to be serviced?

Clause 4.12.4 of IFS Food 8 requires maintenance to be performed at least once every 12 months, as well as whenever significant changes occur.

What does fail-safe mean for metal detectors?

Fail-safe means that if a system component fails, no uninspected product can pass through unnoticed. Typical examples include sensors for ejection confirmation, full or open ejection bins, and compressed air failure. BRCGS requires these functions to be included in routine testing.

Is a metal detector sufficient for foreign object detection?

For metallic foreign objects, usually yes; for glass, stone, bone, or plastic, no. Whether additional X-ray inspection, sieves, or magnets are required depends on your hazard analysis; FSSC 22000 and BRCGS require a documented assessment for this.

Quellen

Weitere Wissensartikel

Get your personal demo

Our product specialists will help you find the perfect machines for your requirements

Name
Company
Email
Phone number
Thank you! Your submission has been received!
Oops! Something went wrong while submitting the form.
By submitting this form you agree with our Privacy Policy.